用icem划分的网格导入cfx中求解出错时怎么回事,错误提示显示说:请看问题补充
来源:学生作业帮 编辑:搜搜做题作业网作业帮 分类:综合作业 时间:2024/08/08 10:18:11
用icem划分的网格导入cfx中求解出错时怎么回事,错误提示显示说:请看问题补充
The specified velocity vector on the boundary patch |
| |
| r1 |
| |
| has a significant normal component at one or more faces.One of |
| these face locations is |
| |
| (x,y,z) = ( 1.26262E+00,1.02654E-01,3.90449E+00).|
| |
| The angle between the specified velocity and the element surface is|
| 89.755 degrees at this face.This is considered an error because |
| it implies that the mesh is moving.The following are possible |
| reasons for the error message:|
| 1.There is a setup error; for example,an incorrect axis of |
| rotation.|
| 2.There may be a meshing problem; for example,the nodes on a |
| rotating surface might not lie on the surface of revolution.|
| 3.The boundary is curved and the mesh is very coarse.In this |
| case,you may increase the tolerance for this check by |
| increasing the expert parameter 'tangential vector tolerance' |
| from its default of 20 degrees.
The specified velocity vector on the boundary patch |
| |
| r1 |
| |
| has a significant normal component at one or more faces.One of |
| these face locations is |
| |
| (x,y,z) = ( 1.26262E+00,1.02654E-01,3.90449E+00).|
| |
| The angle between the specified velocity and the element surface is|
| 89.755 degrees at this face.This is considered an error because |
| it implies that the mesh is moving.The following are possible |
| reasons for the error message:|
| 1.There is a setup error; for example,an incorrect axis of |
| rotation.|
| 2.There may be a meshing problem; for example,the nodes on a |
| rotating surface might not lie on the surface of revolution.|
| 3.The boundary is curved and the mesh is very coarse.In this |
| case,you may increase the tolerance for this check by |
| increasing the expert parameter 'tangential vector tolerance' |
| from its default of 20 degrees.
![用icem划分的网格导入cfx中求解出错时怎么回事,错误提示显示说:请看问题补充](/uploads/image/z/7596917-53-7.jpg?t=%E7%94%A8icem%E5%88%92%E5%88%86%E7%9A%84%E7%BD%91%E6%A0%BC%E5%AF%BC%E5%85%A5cfx%E4%B8%AD%E6%B1%82%E8%A7%A3%E5%87%BA%E9%94%99%E6%97%B6%E6%80%8E%E4%B9%88%E5%9B%9E%E4%BA%8B%2C%E9%94%99%E8%AF%AF%E6%8F%90%E7%A4%BA%E6%98%BE%E7%A4%BA%E8%AF%B4%EF%BC%9A%E8%AF%B7%E7%9C%8B%E9%97%AE%E9%A2%98%E8%A1%A5%E5%85%85)
提示出了问题网格的位置,在ICEM中好好查看下,根据列出的可能原因进行排查.
用icem划分的网格导入cfx中求解出错时怎么回事,错误提示显示说:请看问题补充
icem划分的网格导入fluent时出错
Fluent导入Icem网格错误,设旋转周期错误.
ICEM网格划分问题你好!初用ICEM划分网格,遇到一些问题,恳请相助,不胜感激.我模拟的是多相流在多孔介质中的传热,介
ICEM划分网格问题 小弟最近利用ICEM划分模型的网格,在800mm长的圆柱形流场中 有一个最小几何尺寸仅0.3mm的
关于gambit划分网格和fluent导入的问题
cad导入之后,网格划分出现这样的问题.
用ICEM-CFD软件划分流体网格,怎么只对实体之外的流体画网格啊?
icem建好模型,定义好边界的名称,划分网格,最后导入fluent,边界有丢失部分,发现出口跟wall 在一组里
icem建的网格导入fluent里计算时经常出错
ICEM 划分网格的时候,只有面上有网格但是里面没有(建模用solidworks建的,都是面不是体)
我在ansys网格划分中遇到这样的提示,