英语翻译1.identified mold with mold number2.part shall be free o
来源:学生作业帮 编辑:搜搜做题作业网作业帮 分类:英语作业 时间:2024/08/19 13:54:24
英语翻译
1.identified mold with mold number
2.part shall be free of any flaws and flash shall not not exceed .127mm
3.identify part with mold-in recycable symbol
sensormatic part no.and revision level as shown
place revision characters on insert or ejector pin
for easy replacement character to be 1.5mm HT
4.dimensions enclosed in slots 口 are for critical incoming inspection
我只能翻译个大概,谁能帮我详细的解说下.
5.
For three plate pin point gate mold this sprue bushing should hot sprue bushing and not cold sprue bushing.TSRs state hot sprue and not cold runner
6.
Leaving the current cold runner sprue bushing based on below design this mold will not be able to run fully automatic since this should bolt will not allow the runner ejector plate to strip the sprue runner of the mold.
7.
Suckers (Reverse taper) pin should have sleeve around it to minimize wear in whish will create flash in the runner causing runner to hang in the mold.
1.identified mold with mold number
2.part shall be free of any flaws and flash shall not not exceed .127mm
3.identify part with mold-in recycable symbol
sensormatic part no.and revision level as shown
place revision characters on insert or ejector pin
for easy replacement character to be 1.5mm HT
4.dimensions enclosed in slots 口 are for critical incoming inspection
我只能翻译个大概,谁能帮我详细的解说下.
5.
For three plate pin point gate mold this sprue bushing should hot sprue bushing and not cold sprue bushing.TSRs state hot sprue and not cold runner
6.
Leaving the current cold runner sprue bushing based on below design this mold will not be able to run fully automatic since this should bolt will not allow the runner ejector plate to strip the sprue runner of the mold.
7.
Suckers (Reverse taper) pin should have sleeve around it to minimize wear in whish will create flash in the runner causing runner to hang in the mold.
![英语翻译1.identified mold with mold number2.part shall be free o](/uploads/image/z/5854879-55-9.jpg?t=%E8%8B%B1%E8%AF%AD%E7%BF%BB%E8%AF%911.identified+mold+with+mold+number2.part+shall+be+free+o)
1.鉴定/确认模具标有号码.
2.部件应无瑕疵,闪光灯不应超过127mm.
4.随附在槽里的尺寸规格是为方便临界进料检验.
2.部件应无瑕疵,闪光灯不应超过127mm.
4.随附在槽里的尺寸规格是为方便临界进料检验.
英语翻译1.identified mold with mold number2.part shall be free o
模具英语翻译Identify part with Mold-in recycable symbolsensormatic
英语翻译Vendor shall stamp or engrave the mold base with the mol
英语翻译Complete mold design prints and detail files shall be su
英语翻译Mold shall have adjustable side-surfaces enabling the mo
英语翻译A shake-out machine for use with a self-curing mold whic
英语翻译NOTE!1.PERMANENT MOLD ALUMINUMCASTING ALLOY 356A T62.PAR
mold shrinkage 是什么意思
over mold 怎么翻译
英语翻译Update your procedures and training to ensure mold techn
fine family mold怎么读
英语翻译Pls also provide check model cost.The mold insert you sh